Skip to content
img
Tremco - Commercial

ExoAir® 220

Fluid-Applied, Asphaltic Air & Vapor Permeable Membrane ExoAir® 220 Fluid-Applied Permeable Air Barrier Membrane is a monolithic, elastomeric membrane designed to be rolled or sprayed onto exterior above-grade wall assemblies to mitigate air infiltration/exfiltration and water penetration while remaining permeable to the passage of water vapor. Basic Uses ExoAir 220 is typically applied to exterior sheathing panels, concrete block, poured concrete or wood substrates as an air and vapor barrier material. ExoAir 220 can be used with ExoAir 110, ExoAir 110AT or Dymonic® 100 liquid flashing to detail into the rough opening.

Download Data Sheet

ExoAir® 230/230LT

Fluid-Applied, Synthetic Air & Vapor Permeable Membrane ExoAir® 230 Fluid-Applied Synthetic Permeable Air Barrier Membrane is a monolithic, elastomeric membrane designed to be rolled or sprayed onto exterior above-grade wall assemblies to mitigate air infiltration/exfiltration and water penetration while remaining permeable to the passage of water vapor. Basic Uses ExoAir 230 is typically applied to exterior sheathing panels, concrete block, poured concrete or wood substrates as an air and vapor barrier material. ExoAir 230 can be used with ExoAir 110, ExoAir 110AT, ExoAir 230 with mesh as fluid-applied flashing or Dymonic® 100 liquid flashing to detail into the rough opening.

Download Data Sheet

Securock® ExoAir® 430

Securock® ExoAir® 430 pre-applied fluid-applied synthetic permeable air/water barrier membrane is a monolithic, elastomeric membrane that is applied in a factory setting eliminating the inconsistencies and weather impact that can occur when applied in the field. It is applied to the face of USG Securock® Brand Ultralight Glass-Mat Sheathing panels for above-grade wall assemblies to mitigate air infiltration/exfiltration and water penetration while remaining permeable to the passage of water vapor.

Download Data Sheet

ExoAir® 130

Fluid-Applied, Synthetic Air and Vapor Retarder Membrane ExoAir® 130 Fluid-Applied Synthetic Air and Vapor Barrier Membrane is a monolithic, elastomeric membrane designed to seal exterior above-grade wall assemblies and mitigate air infiltration/exfiltration, vapor transmission and water penetration. It is available in a single grade that can be roller or spray applied using the appropriate spraying equipment. Basic Uses ExoAir 130 is typically applied to exterior sheathing panels, concrete block, poured concrete or wood substrates as an air and vapor barrier material. ExoAir 130 can be used with ExoAir 110, ExoAir 110AT or Dymonic® 100 liquid flashing to detail into the rough opening.

Download Data Sheet

ExoAir® 120

Fluid-Applied, Asphaltic Air & Vapor Barrier Membrane ExoAir® 120 Fluid-Applied Air and Vapor Barrier Membrane is a monolithic, elastomeric membrane designed to seal exterior above-grade wall assemblies and mitigate air infiltration/exfiltration, vapor transmission and water penetration. Basic Uses ExoAir 120 is typically applied to exterior sheathing panels, concrete block, poured concrete or wood substrates as an air and vapor barrier material. ExoAir 120 can be used with ExoAir 110, ExoAir 110AT, ExoAir 111 or Dymonic® 100 liquid flashing to detail into the rough opening.

Download Data Sheet

ExoAir® 110AT

Self-Adhered Air and Vapor Barrier Membrane ExoAir® 110AT is a 22-mil composite impermeable membrane that is comprised of 16 mils of butyl and 6 mils of HDPP facer. It can be used as the membrane, detailing accessory, as well as thru-wall flashing of an air barrier system. ExoAir 110AT when installed properly as a system will provide the requirements of an air barrier: air impermeable, continuity, structural integrity and durability. Basic Uses ExoAir 110AT is an impermeable, self-adhered sheet designed to be applied to exterior cavity walls in order to mitigate air infiltration/exfiltration, vapor transmission and water penetration. Typically applied to exterior sheathing boards and concrete block, ExoAir 110AT can also be applied to poured concrete, steel, wood based, Nudura Insulated Concrete Forms (ICF), and insulated concrete forms substrate, as well as serve as detailing or a transition membrane into window and door openings. ac_unit ExoAir 110AT is designed to be installed when both the air and surface temperature is 20°F (-7°C) and rising. 20°F (-7°C)

Download Data Sheet

Proglaze® ETA

Engineered Transition Assembly Proglaze® ETA is a pre-engineered silicone materials used as a transition assembly between the window or wall system and adjacent air and vapor barrier materials. The assembly is comprised of a flat single or double ribbed silicone extrusion of varying widths, which is adhered to the building façade with Spectrem 1 Silicone Sealant to ensure a durable connection and positive seal. The opposite edge of the ribbed silicone extrusion will span unsupported onto the wall and/or window system, which is adhered with Spectrem 1 Silicone Sealant. This connection will provide a long-term durable flexible connection between the two components. Basic Uses Proglaze ETA is applied as an air and vapor barrier transition assembly for connecting continuously between the window and/or wall openings and the adjacent air and vapor barrier materials. It can be used to span and seal across irregular window geometries. Proglaze ETA Connections can be used at junctions between other assemblies within the building envelope where spanning of voids is commonplace, such as roof to wall, floor deflection joints, expansion and control joints or any other location where a degree of movement is anticipated.

Download Data Sheet

Proglaze® ETA 3-D Molded Corners

Proglaze® ETA 3-D Molded Corner Connections are engineered from 40 Durometer Dense Translucent Silicone used for making connections to our ExoAir® Air Barrier Membrane systems with Spectrem® 1 Silicone Sealant. The 3-D molded corners have been designed in such a way so that they may be used to overlap one another or used in conjunction with other Proglaze ETA components to accommodate complex transitions. Basic Uses Proglaze ETA 3-D Molded Corner Connections are designed to facilitate transitions when construction sequencing has the surrounding façade being installed prior to the wall or window system. ETA is compatible with and recommended for use with all Tremco ExoAir Air Barrier products. Allows complex connections to the wall or window system, which may be recessed or set proud from the plane of the weather barrier surface. Field fabrications of saddle-flashings. Transitions the weather barrier across seismic drift joints at the heads of punched openings. Ability to create a flexible sill pan.

Download Data Sheet

Proglaze® ETA Connections

Proglaze® ETA Connections are pre-engineered silicone materials used as a transition assembly between the window or wall system and adjacent air and vapor barrier materials. The assembly is comprised of a flat single or double ribbed silicone extrusion of varying widths, which are adhered to the building facade with Spectrem® 1 Silicone Sealant to ensure a durable connection and positive seal. The opposite end of the ribbed silicone extrusion will span unsupported onto the wall and/ or window system, which is adhered with Spectrem 1 Silicone Sealant. This connection will provide a long-term durable flexible connection between the two components. Basic Uses Bridge continuously between the window and/or curtain wall and the adjacent air and vapor barrier materials. Absorb thermal movement and wind-loading stresses. Allow the material to span and seal across irregular window geometries. Allows the installer and/or inspector to see through the gasket to verify the recommended amount of sealant is properly applied to ensure an effective seal is achieved, while the ribs of the gasket’s design ensures a minimum sealant thickness.

Download Data Sheet

ExoAir® 110

Self-Adhered Air & Vapor Barrier Membrane ExoAir® 110 is a composite 40-mil sheet designed to be a component of an air barrier system. ExoAir 110 is 36 mils of self-adhering SBS rubberized asphalt laminated to 4 mils of white, cross-laminated, high-density polyethylene film and a siliconized release liner. Basic Uses ExoAir 110 is typically applied to exterior sheathing boards and concrete block, but can also be applied to poured concrete, steel and wood based substrates. ExoAir 110 also serves as a detailing or transition membrane into window and door openings. ExoAir 110 is designed to be installed when both the air and surface temperature are 30 °F (-1 °C) and rising.

Download Data Sheet

ExoAir® Termination Mastic

Mastic for Use with ExoAir Self-Adhered Membranes ExoAir® Termination Mastic is a single component mastic formulated from polymers, plasticizers and select additives. It is carefully blended to ensure elasticity, weather resistance and durability with ease of application. Basic Uses ExoAir Termination Mastic is designed to seal T-joints, overlaps in detail areas and as a repair mastic for ExoAir 110, TWF, ExoAir 120 and ExoAir 220.

Download Data Sheet

POLYshim® II Tape

High-Performance Glazing Tape POLYshim® II Tape is a 100% solids, highly adhesive and elastic, cross-linked butyl preformed tape with a continuous integral EPDM shim. Basic Uses POLYshim II Tape is used in compression glazing systems wherever the design calls for high-performance glazing of curtain wall, unitized curtain walls, punched and ribbon window systems, and sloped glazing applications.

Download Data Sheet

SGT-900 Series

Structural Glazing Tapes Tremco SGT-900 Series Structural Glazing Tapes are open-cell, high density polyurethane foam tapes with a micro-cellular structure. Basic Uses SGT-900 Series Tapes have been specifically developed to be utilized as a compatible spacer for Structural Glazing Systems. The tapes are available in a wide variety of sizes with single or double-faced, pre-applied, pressure-sensitive adhesive.

Download Data Sheet

Tremco ET 675

Extruded Flow-Resistant Tape Tremco ET 675 is a 100% solid, cross-linked preformed (extruded) butyl tape. Tremco ET675 is non-oxidizing, non-film forming, and provides exceptional flow resistance when subjected to vibration Basic Uses Tremco ET 675 is used for concrete to concrete seals and glass to metal seals. ET 675 also is used to separate dissimilar metals to prevent galvanic action, and seal out moisture and air infiltration for roof and side panel lap joints. Tremco ET 675 exhibits superior adhesion to a wide variety of treated and untreated surfaces including metal, wood, glass, and plastic surfaces.

Download Data Sheet

Tremco® 440 Tape

Butyl Sealant Tape Tremco® 440 Tape is a 100% solid Polyisobutylene cross-linked butyl, preformed sealant. Basic Uses Tremco 440 Tape is used for non-compression glazing of vision lites and spandrel panels in PVC metal and wood frames, in low-rise building construction, not exceeding 75 UI. Tremco 440 Tape is also used for lap sealing between panels such as steel, aluminum and porcelain as well as a variety of other joints subject to shear between similar and dissimilar materials.

Download Data Sheet

VISIONstrip

Precision-Extruded Glazing Seal VISIONstrip® is a precision-extruded glazing seal consisting of an EPDM rubber extrusion positioned at the sightline with a 100% solids, highly adhesive, cross-linked performed butyl sealant bonded below the rubber extrusion. A single component profile achieving a positive-wet seal between the metal and glass surfaces while providing a clean gasket appearance at the sightline. Basic Uses VISIONstrip is used in compression glazing systems wherever the design calls for high performance glazing of curtain wall, unitized curtain walls, punched and ribbon window systems and sloped glazing applications.

Download Data Sheet

Arrow-Shim Gaskets

Continuous Spacer Shims Arrow-Shim Extrusions are used recessed between sash and glass or plastic sheet in conjunction with a sealant cap bead. Arrow-Shim Extrusions are designed to control and provide proper face clearance cap bead spacing while providing a uniform cushion along the entire perimeter of the glass. Easier to install than round shims. Basic Uses Arrow-Shim Extrusions, designed for use in combination with Tremco silicones, glazing tapes, and gaskets, can be incorporated into many glazing systems that will handle those unique projects with off-the-shelf, single source glazing components.

Download Data Sheet

Cellular Rubber Extrusions

Tremco Cellular Rubber Extrusions are fabricated into gaskets and accessories for use in sealing and glazing applications in building construction. Rubber Extrusions are generally custom manufactured but many standard designs are available. Many profiles are available depending upon existing metal requirements. Basic Uses Customized product is based on customer requirements, profile size, configuration and the need for molded picture frame gaskets.

Download Data Sheet

EPDM Dense Rubber Extrusions

Dense Rubber Extrusions Tremco EPDM Dense Rubber Extrusions are extruded and fabricated into gaskets and accessories (such as setting blocks, spacers and shims) for use in sealing and glazing applications in building construction. Basic Uses Tremco EPDM Dense Rubber Extrusions are manufactured to work with existing metal designs or custom developed with custom metal systems at the design development stage. Many profiles are available depending upon existing metal requirements.

Download Data Sheet

Neoprene

Flame-Retardant Dense Rubber Extrusions Tremco Flame Retardant Dense Neoprene Rubber Extrusions are extruded and fabricated into gaskets and accessories (such as setting blocks, spacers and shims) for use in sealing and glazing applications in building construction. Basic Uses Tremco Flame Retardant Dense Neoprene Rubber Extrusions are manufactured to work with existing metal designs or custom developed with custom metal systems at the design development stage. Many profiles are available depending upon existing metal requirements.

Download Data Sheet

Peroxide EPDM Extrusions

Rubber Extrusions Tremco Peroxide EPDM Rubber Extrusions are extruded and fabricated into gaskets and accessories (such as wedges, pre-set spacers, weatherstripping and shims) for use in glazing applications and other building joint applications. Basic Uses Tremco Peroxide EPDM Rubber Extrusions are manufactured to work with existing metal designs or custom developed with custom metal systems at the design development stage. Many profiles are available depending upon existing metal requirements.

Download Data Sheet

Poly-Wej Gaskets

Tremco Poly-Wej Gaskets are designed for use in compression glazing systems. They are available as a standard in EPDM. When used in combination with Tremco POLYshim® II Tape and gunnable sealants, the Poly-Wej Glazing System is formed. This system is proven and “clean and easy” to install, affording many years of excellent performance. Basic Uses For use in compression glazing systems.

Download Data Sheet

SCR-900

Silicone Compatible Rubber Extrusions SCR-900 Silicone Compatible Rubber Extrusions are fabricated into gaskets and accessories (such as wedges, pre-set spacers, weatherstripping, setting blocks and shims) for use in glazing applications and other building joint applications. Basic Uses Fabricated for use as gaskets, wedges, pre-set spacers, weatherstripping, setting blocks and shims in various glazing applications. Can be used in other building joint applications. Many profiles are available depending on existing metal requirements or designs may be developed for use with custom metal systems.

Download Data Sheet

Silicone Extrusions

Dense Rubber Extrusions Tremco Silicone Dense Rubber Extrusions are extruded and fabricated into gaskets and accessories (such as setting blocks, spacers and shims) for use in sealing and glazing applications in building construction. Custom color matching is available. Basic Uses Tremco Silicone Dense Rubber Extrusions are manufactured to work with existing metal designs or custom developed with custom metal systems at the design development stage. Many profiles are available depending upon existing metal requirements

Download Data Sheet

Spectrem® Restoration Overlay

Spectrem® Restoration Overlays are dense rubber extrusions used for restoration applications. The patented, innovative design solution provides long-lasting performance and aesthetics. These overlays are typically bonded with Spectrem 1 Silicone Sealant to provide a watertight seal. Basic Uses Spectrem® Restoration Overlays are custom designed to restore aging and/or compromised glazing systems including skylights, sloped glazing, zipper wall/lockstrip systems, and pressure bar systems. Cost effective alternative to traditional dry glazing repair method involving total removal and replacement of the system components Reduced time and labor versus other repair methods Less sealant versus other repair methods Easy installation and clean-up Better long-term performance against air and water leakage compared to traditional dry glazing repair method Color fast formula resistant to the effects of UV exposure Encapsulated wet seal is protected from exposure to the elements High movement capability Better overall aesthetic with sealant minimally visible providing straight sight lines on the interior and exterior for a clean appearance All joineries, screw heads, and other penetrations are covered Wide operational temperature range Non-corrosive and corrosion resistant Allows for ease of glass infill/other infill replacement for on-going maintenance.

Download Data Sheet

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods